ok so im looking to find a snug cage that fits me. thing is im pretty small. i sit at 1.5 maybe 2 inch soft and 4.5 inch hard. (dont think hard has anytthing just idea for measure) is tehre any affordable cages that i can get to start off that will fit snug? one i had found that seems ok is this https://www.amazon.com/Utimi-Silica-Chastity-Device-Special/dp/B00MBDZLAI/ref=cm_cd_al_qh_dp_i and opinions?
The one you link is so easy to defeat it is laughable.... You are not the smallest here by quite a bit!!!!!. There is a metal cage thst fits small soft cocks..... Examples in my gallery. Otherwise I'm in the birdlock Pico and it is proving to be quite effective...
it sure seemed like it but its all i could really find to be honest^^; and really? well maybe not the smallest but sure seems hard to find a dang cage hehe i think i saw the one. http://chastitymansion.com/forums/index.php?gallery/photos/16015/ this one right? it does have me intrested ^//^
did forget! that while im soft that lenght i do scrunch up like if it was cold. but without the cold lol. so i scrunch to like an inchish
go on amazon, the have tons of affordable ones. ot look on chastity cages here for better ones. good luck
I would suggest this one on ebay. Just do an ebay search for: Stainless Steel 6CM Male Chastity Device It has the integrated lock. the welds are better than most Chinese SS devices. It is SMALL. 1.25" ID tube, and short in length as well. Some have recommended the device with curved base ring & curved tube rings, but I would think many could sqeeze their ball out where the gap is biggest, and totally remove those devices. I haven't tried one with the curved rings myself. BTW, for me, the optimal lower GAP (at the bottom of the O ring) is .60". And that is moving around the ruler/ caliper to find the angle with the biggest gap (I think many CB makers define the "gap" as the "side view", measuring lines that are parallel to the O ring). But the actual biggest GAP that a ball could slip through will be bigger if the cage entry ring is smaller than the O RING. Good luck!
Maybe look on DHGate I got mine on eBay, which was less expensive than Amazon, and saw the same cage for about $8 less at DHGate $25
I have the medium sized version of this device and I've found out after a few days of wear that there is too much play once the lock is inserted and the cage can rotate enough so the two posts come out of the base ring. I don't know if I've simply bent those posts or if it is an issue with my device. When it first happened I noticed it because I had a ball pop out. I thought about getting another one since they are so cheap.
My little bslls slip out now and again... http://www.chastitymansion.com/forums/index.php?gallery/photos/tiny.13317/®ular=1
I have the same dimensions as him and literally fell out between the cage and my balls so often it was silly to wear. Had the bird locked pico
I too have the birdlock peco, more reliable can't pull out at will....but still do have occasions when I find it in my knickers and not attached
I went ahead and ordered another one. So far these last few weeks is the longest I've been locked, since the 13th of July. I plan on trying 30 days of complete denial starting at the beginning of next year and if that goes well, then maybe I'll look to drop the $400 plus it takes for some custom metal.
These Chinese devices are tricky to order and get what you really want. The listing with S, M & L is a different manufacturer than the photo I posted. The alignment pins are smaller and the welds are much smaller and less professional. One problem I've had with the Chinese devices is that the O ring size varies (from 1.50" to 1.65" ID when you ask for 40mm), and the GAP at the bottom varies from an unusable .30 to .70 or so. And the alignment pins are sometimes far too weak to make the cage hold it's shape, and sometimes too short and they can fall out of the O RING. I think The MOST IMPORTANT sign of a cage not to buy is if the O-ring to cage connection is a SIDEWAYS pin that sqeezes together tabs. I have been remaking my Chinese devices by: > cutting off alignment pins, enlarging hold to .125 for stiff .125 Stainless rod pins, then welding these strong pins to the cage to provide the .60 max. bottom gap that I prefer. > Cutting off and re welding the center part of the integrated lock to ensure TIGHT locking at new geometry. The result of these is a TIGHT cage that must be wiggled a few times to open, and NO play or pinching anywhere. > If the O ring is not between 1.60 & 1.63, I cut it and bend it in the vise & reweld, grind, sand & polish it back like new. > I have also removed an entire cage ring to shorten a cage. > Bend rings in cage closer togehter or farther apart in vice to get desired length.