Thank you to Mark

I’ve worn a Glans Amor cage for 27,180 hours. Over three years of wear. In 2023 I wore it for 3,696 hours straight without a moment unlocked. I began to call it my dream home, and my forever cage.

Congratulations! I hope you enjoy it
 
  • Like
Reactions: Maddie Mae, Tom_S and Slutty Susan
Which piercing are you using or is it the glans ring non pierced version?

What's the measuring /fit like?

I'm currently not pierced , I've been experimenting with the teatherspout but gone off that idea. I've looked at the GA2 with the glans ring but having unsuccessfully tried using an existing cage with the TS no base ring , it was sliding around as the spout tip is quite long and as a grower, the cage be half way up my shaft when hard.
I'm guessing the ID of the cage has to be just right not too lose but not too tight either.
We do like the appeal of ditching the base ring, it'd be amazing , make it easier to get the cage on/off hard or soft etc

I've got the go ahead for a frenum piercing and will be looking again for a new cage to use the piercing when healed. I do like the look of a frenum loop/ring but not sure about long term comfort wear or if/how it could be used with a cage.
I'm also considering the Evotion Bajou but again not sure about sizing/fit and from what I understand it's difficult/impossible to get on/off when hard.
 
I have a PA @Andy007 currently at 4 gauge, I am a grower and as you say the fit needs to be right. It is certainly good to not have a base ring.
 
@Andy007 I would stretch to wear a 4ga Prince Albert hook. 6ga may have worked for me if I waited longer.

I did find stretching pretty easy after my first size jump. I was patient and careful.

I’m pretty fleshy being a grower, and loosely cut. So moving parts inside the cage never worked for me: trapping rings, or moveable PA parts. I even got annoyed by the wobble that some of Lori’s allowed. I get pinched really easy.

But every penis is different.

I need a fixed hook, and Mark’s don’t move… in a GlansArmor or a Contender. They fasten down and stay there.
 
  • Like
Reactions: Maddie Mae
Peter Rabbit said:
@Andy007 I would stretch to wear a 4ga Prince Albert hook. 6ga may have worked for me if I waited longer.

I did find stretching pretty easy after my first size jump. I was patient and careful.

I’m pretty fleshy being a grower, and loosely cut. So moving parts inside the cage never worked for me: trapping rings, or moveable PA parts. I even got annoyed by the wobble that some of Lori’s allowed. I get pinched really easy.

But every penis is different.

I need a fixed hook, and Mark’s don’t move… in a GlansArmor or a Contender. They fasten down and stay there.
Click to expand...
Yeah I'm a grower too. I would've thought having a moving part be beneficial so not constantly stretched out or not too much pressure on the piercing when erect ...
 
Any recommendations on how to get ahold of MCN? The website is wonky. I’ve tried registering and sending messages but kept getting error messages. Is Mark active here at Chastity Manson?
 
Andy007 said:
I'm guessing the ID of the cage has to be just right not too lose but not too tight either.
We do like the appeal of ditching the base ring, it'd be amazing , make it easier to get the cage on/off hard or soft etc

I've got the go ahead for a frenum piercing and will be looking again for a new cage to use the piercing when healed. I do like the look of a frenum loop/ring but not sure about long term comfort wear or if/how it could be used with a cage.
Click to expand...

To obtain your correct cage diameter use rubber test rings, available in the same sizes as the rings I make from the following vendor...

https://male-essentials.com/product/nitrile-rubber-cock-rings-rras/

If in doubt when ordering from me it's always best to choose an i.d. that's wider because I can always "tighten" a Glans Armor by welding a slightly narrower ring to the original ring.

I can't widen an i.d. once a cage is made since it is built upon the chosen ring size.

Unfortunately, I can't make a version of the Glans Armor for a frenum piercing, which I personally have not found to be very comfortable to wear due to my skin getting pinched between the pin and the lock cylinders.

There's no space to pinch skin in the lock setup on the Glans Armor with a PA pin, and mine is super comfortable.

For anyone who has purchased a Glans Armor with the rubber glans ring, and who is considering getting a PA piercing, a PA pin can be purchased at a later date that will fit your Glans Armor.
 
Slutty Susan said:
Mark is prompt in replying to emails

zemanem@gmail.com
Telephone:
(206) 250-7598
Click to expand...

My preferred method of contact is via the email address above.

Texts and phone messages seem to have a tendency to slip out of my awareness very quickly if I don't respond to them the moment they arrive, which is not always possible due to the multitude of things continually vying for my attention (I may be driving while listening to vm's, focused on fabrication when a call arrives, or distracted/focused on other issues at hand).

You'll always get a faster response from me via email since I spend a lot of time at the computer answering emails before or after fabricating a day's orders.

Cheers!
Mark
 
  • Like
Reactions: Slutty Susan
You must log in or register to reply here.
Top Bottom