Not sure in which Forum I should post this but as I'm a Newbie to this site thought it best to start here
Hi
I've read a couple of threads that mention Tetherspout but have a few questions of my own so rather than hijacking someones thread thought it best to start a new one. Sorry if this is all repeated questions.
I’m interested in using a Tetherspout. To a) tether to a cage and b) enable me to pass urine standing up while caged. I’ve tried using long and short tight fitting catheters that have been fixed to a cage but I tend to leak down the side of the catheter and also dribble a little after I’ve finished.
A couple of years ago I purchased one of Tetherspouts measuring devices so know my urethra size in FR dimensions. (33Fr or 10.89mm). For comfort reasons Tetherspouts website recommends going for one or two FR sizes smaller. Is this what other users have discovered? This seems counter to what would be the logical requirement for an object to be retained and give a good seal to the urethra or is this using the elliptical retainers in the set of three rather than the round one?
Tetherspout’s shop now only has one size spout available and though it is a threaded version, which is initially what I was thinking of purchasing a couple of years ago, it is the short spout. All retainers are still listed as available so I was thinking of purchasing the retainers from Tetherspout. I’ve then been mulling over whether to go straight for the metal retainers or start off ordering the Nitrile rubber versions to trial fit before forking out for the metal equivalents.
Then I’m thinking or ordering the spout itself from either Badassworkroom (The E1 which has a 6mm diameter)
https://badassworkroom.com/collecti...roducts/tetherspout-for-non-piercing-chastity
or this one on esty?
https://www.etsy.com/ie/listing/987800247/men-chastity-device-urethral
The problem I have is the compatibility with the one on esty and Tetherspout retainers. Does anyone know the diameter of the esty spout?
Any thoughts, experience of using Tetherspout also of the components from any of the above suppliers would be greatly appreciated.
Thanks
Hi
I've read a couple of threads that mention Tetherspout but have a few questions of my own so rather than hijacking someones thread thought it best to start a new one. Sorry if this is all repeated questions.
I’m interested in using a Tetherspout. To a) tether to a cage and b) enable me to pass urine standing up while caged. I’ve tried using long and short tight fitting catheters that have been fixed to a cage but I tend to leak down the side of the catheter and also dribble a little after I’ve finished.
A couple of years ago I purchased one of Tetherspouts measuring devices so know my urethra size in FR dimensions. (33Fr or 10.89mm). For comfort reasons Tetherspouts website recommends going for one or two FR sizes smaller. Is this what other users have discovered? This seems counter to what would be the logical requirement for an object to be retained and give a good seal to the urethra or is this using the elliptical retainers in the set of three rather than the round one?
Tetherspout’s shop now only has one size spout available and though it is a threaded version, which is initially what I was thinking of purchasing a couple of years ago, it is the short spout. All retainers are still listed as available so I was thinking of purchasing the retainers from Tetherspout. I’ve then been mulling over whether to go straight for the metal retainers or start off ordering the Nitrile rubber versions to trial fit before forking out for the metal equivalents.
Then I’m thinking or ordering the spout itself from either Badassworkroom (The E1 which has a 6mm diameter)
https://badassworkroom.com/collecti...roducts/tetherspout-for-non-piercing-chastity
or this one on esty?
https://www.etsy.com/ie/listing/987800247/men-chastity-device-urethral
The problem I have is the compatibility with the one on esty and Tetherspout retainers. Does anyone know the diameter of the esty spout?
Any thoughts, experience of using Tetherspout also of the components from any of the above suppliers would be greatly appreciated.
Thanks